The Expanding Frontier

Creating Sci-fi RPG Resources

  • Home
  • Order a Map
  • Order Miniatures
  • Supporters
  • About
  • Bio

Moonbright Stinger Miniature and Model (aka The Gullwind)

  • 3D Models
  • Starships

It’s been over seven months since I last posted a miniature. And a month and a half since I posted anything at all. I didn’t get back to posting in May like I had hoped but I have started working on projects again. I just haven’t found time to write up the posts. That will probably continue through mid-July (once I finish the next issue of the Frontier Explorer) but things should start picking up after that.

Which brings us to the Moonbright Stinger model. This is a miniature from the Privateers boxed set. I had mentioned in the past that I had all the miniatures from that set that I had collected loose, but not from a single set. I also mentioned that I had misplaced three of the minis. Several people offered to send me theirs so I could use them to recreate the miniatures. I’m grateful to those that offered. However, during the intervening months when I wasn’t posting, a new, still in shrink-wrap Privateers boxed set came up on Ebay. While I’ve been burned with sealed minis having lead rot, that has only been on the Federation Ships boxed set. I’ve never had an issue with any other ones. I really think it was something in the production run of that particular set of minis.

In any case, I decided to take the chance and exercised the “Buy it now” option on Ebay and purchased the miniature set. It arrived a few days later and when I opened it up, I was happy to discover that the figures were in pristine condition.

Miniatures from my new Privateers boxed set. The Moonbright Stinger with its engine that needs to be attached is there at the bottom left.

I had already started working on the Moonbright Stinger model by then as it was one of the ones I still had, but this gave me a second miniature to compare to. The name Moonbright Stinger is the name of the miniature that is give on the Privateers box. Most Star Frontiers gamers know a much more famous ship of the same class. In fact, after the assault scout, this is probably the second most iconic ship of the game. Of course I’m referring to the Gullwind, which features in the Dramune Run module:

The Gullwind. From SFKH:1 The Dramune Run, p 6.

And while the miniature doesn’t quite have the detail of the artist’s drawings, it’s pretty close.

The 3D Model

Final model

The above is a render of the completed 3D model as seen from the “top” of the ship. The decks are perpendicular to the thrust axis as is true for all ships in Star Frontiers, but the artists like to draw this ship this way so I oriented the image that way as well.

The basic body of the ship

This model was a bit complicated but I think of all of the Privateer models, it’s going to be the easiest to recreate so that’s why I started with it. I began by roughing out the body. The engines were easy as was the fuselage up through the cargo bay (that large cylinder at the back). Forward of the cargo bay, the “underside” (not seen) is cylindrical while the “top” is a trapezoid. It took a little bit of jiggling to get that just right and in the end, I ended up making the top of the trapezoid a bit too wide but not enough to worry about.

The other thing is the nose of the ship is 1) not perfectly round, and b) off-center from the axis of the ship. Luckily my modeling software has a “hull” command that allows you to define a series of shapes at various layers and then the computer will smoothly connect them to form a surface. I used this to do both the nose (below where it became cylindrical) and the transition region from the main body to the nose. The roughed out body is shown in the image to the right. The observant reader may notice that the engines are not lined up in this roughed out version as they are in the final model. I didn’t notice that I did that until I was comparing the printed version of the miniature with the original.

After I had the basic hull done, I added in all the details on the miniature. Adding the positive features was fairly straightforward although those pods on the side of the ship just forward of the cargo bay were a bit tricky. With the easy stuff done, it was time to start adding in the negative details that were cut out of the body of the ship.

Of course life got in the way and there was a five month gap between adding the positive features and when I started added the negative details. I did this in sections, first I added details to the “top” of the ship, working from the cargo bay to the nose. I then went back and added in details on the starboard side and then port side, and finally the the rounded bottom of the ship. While I measured out all the features to get their sizes and positions, the final placement was done by eye to try to match the miniature. In the process, I discovered that I had gotten the length a bit wrong on parts of the ship’s fuselage (the final model is 1mm longer than the original miniature) and had the positions of some of the positive details slightly wrong as well. Positions and sizes (except for that 1mm length difference) were corrected as I went along. That gave us the final model as seen in the images below showing the two sides of the ship.

The “top” and starboard sides of the ship.
The port and “bottom” sides of the ship.

Printing

With the model done it was time to print it out and compare it to the original. Here’s what that first print looked like:

First print compared to the original model.

After putting these next to each other and taking this picture, I noticed a few thing immediately:

  1. I need to get a better camera than just my cell phone for taking close-up (macro) shots. Also, the discoloration on the printed miniature is is probably due to my haste in the cleaning and curing process. I might not have let it dry enough before curing.
  2. This is when I noticed that the engines in the model are rotated 30 degrees from where they should be. I’m not sure how I missed that. The hole in the top of the metal miniature near the back is where the third engine on that mini is supposed to attach when you glue it on.
  3. The positive features are mostly fine, but it turns out the negative feature on the fuselage are not quite deep enough to really make them stand out like they do on the original. I thought that might be the case when I was making the mode and it turns out that I was right. I will need to tweak them all to make them deeper.
  4. The big dome and boxy structure near the nose of the ship are a bit too big. They need to be shrunk down just a tad.
  5. Finally, this is when I noticed that the model is 1mm longer than the original. The discrepancy is in the nose area starting in the transition region down to the smaller nose and the nose section being a bit too long. When I was building the model I noticed I had a bit more space there but wasn’t sure why. I’m not going to fix this.

Observations in hand, I went through and doubled the depth of the negative features, tweaked the size and positions of the positive features, and reprinted the model.

Top and port side
Bottom

And then I noticed I rotated the engines the wrong direction so now they are 60 degrees off instead of 30. Oops. But the negative details stand out much better now and I’m happy with the way it looks. After this print I fixed the engine position and that resulted in the model image at the top of the post. I haven’t since reprinted the model but will at some point.

What’s next?

Next up is one of the smaller Privateer models, the Thruster class. It’s the small one in the upper left of the group picture up above. That one will take some work to get the wing features correct as that smoother shape is not something my CAD software does natively. I did it for the Freighter miniature, so I just need to relearn how.

I will be getting this model up on DriveThruRPG along with the rest of the models there as well as getting a price on to the price list here on this site.

Let me know what you think about this miniature and model in the comments below.

3D Printing Gullwind Knight Hawks miniatures
June 23, 2021 Tom

Post navigation

Back to Blogging → ← State of the Frontier – April 2021

7 thoughts on “Moonbright Stinger Miniature and Model (aka The Gullwind)”

  1. Tom Bertenshaw says:
    July 4, 2021 at 1:28 pm

    Great to see you posting again 🙂 The print looks neat compared to the metal miniature and the engines are straight too. All the more reason to choose this over a metal miniature. I still like the weight of a metal miniature though. It would be interesting to see how they paint up, that would be the real test.

  2. ANDREW LAWTON says:
    July 12, 2021 at 5:04 am

    Brilliant cant wait to add A couple of Atlantic’s to my Freighter fleet for Knighthawk’s Gullwind always a Fave StarFrontiers design, Sort of a “Millinium Falcon” to my old SF Group 🙂

  3. Aemon Aylward says:
    August 7, 2021 at 10:02 am

    I’m really excited to see that you’ve done this mini – thanks! (I’m almost as astonished at myself that, despite owning a set of the privateers minis, and Dramune Run being my favorite module, I’d never realized that the Midnight Stinger was the same class as the Gullwind.)

    As long as I’m writing a note, I’d like to say a quick thanks for all the work you’ve done for the game over the years. I’m signed up at the cheapest level of Patreonage, but that seems awfully little compared to all the enjoyment I’ve gotten and continue to get out of your material. I especially appreciate the depth of scientific background you bring to the hobby.

    Many thanks again, and I hope you are able to keep it up for a long time to come!

  4. ANDREW LAWTON says:
    August 9, 2021 at 4:53 am

    Hi still can’t find It on Drivethru any chance of posing it up soon 🙂

  5. Pingback: Some Random Bits – The Expanding Frontier
  6. Tom says:
    May 24, 2022 at 7:57 pm

    It’s up now.

  7. Pingback: A Look at Yachts and Privateers – The Expanding Frontier

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Become a Patron!

Recent Posts

  • Detailed Frontier Timeline – FY62.069 to FY62.99
  • State of the Frontier – August 2022
  • Battle of Hargut (Gruna Garu) – FY62.098
  • Archived Arcane Game Lore Posts – May 2013 to Dec 2014
  • A Look at Yachts and Privateers
  • Homeworld Bound – A Campaign Concept
  • Second Battle of Fromeltar (Terledrom) – FY62.083
  • Sample Star System Data
  • Detailed Frontier Timeline – FY62.038 to FY62.068
  • State of the Frontier – July 2022

Categories

  • 3D Models
  • Adventures
  • Background
  • Creatures/Races
  • Deck Plans
  • Equipment
  • Game Design
  • General
  • Locations
  • Maps
  • NPCs
  • Optional Rules
  • Patreon-only
  • Project Overviews
  • Reviews
  • Setting Material
  • Starships
  • System Brief
  • Vehicles
  • Writing

Recent Comments

  • Loguar on Detailed Frontier Timeline – FY62.069 to FY62.99
  • Loguar on Detailed Frontier Timeline – FY62.069 to FY62.99
  • Tom on Detailed Frontier Timeline – FY62.069 to FY62.99
  • Rook on Maps and Counters
  • Loguar on Detailed Frontier Timeline – FY62.069 to FY62.99
  • Tom on Detailed Frontier Timeline – FY62.069 to FY62.99
  • Tom on Second Battle of Fromeltar (Terledrom) – FY62.083
  • Loguar on Detailed Frontier Timeline – FY62.069 to FY62.99
  • Loguar on Second Battle of Fromeltar (Terledrom) – FY62.083
  • Aemon Aylward on Sample Star System Data

Archives

  • September 2022 (1)
  • August 2022 (9)
  • July 2022 (3)
  • June 2022 (3)
  • May 2022 (3)
  • June 2021 (1)
  • April 2021 (1)
  • February 2021 (4)
  • January 2021 (6)
  • December 2020 (5)
  • November 2020 (11)
  • October 2020 (4)
  • September 2020 (5)
  • August 2020 (4)
  • July 2020 (6)
  • June 2020 (5)
  • May 2020 (8)
  • April 2020 (5)
  • March 2020 (5)
  • February 2020 (5)
  • January 2020 (5)
  • December 2019 (7)
  • November 2019 (4)
  • October 2019 (6)
  • September 2019 (5)
  • August 2019 (6)
  • July 2019 (7)
  • June 2019 (5)
  • May 2019 (6)
  • April 2019 (7)
  • March 2019 (4)
  • February 2019 (5)
  • January 2019 (7)
  • December 2018 (5)
  • November 2018 (10)
  • October 2018 (4)
  • September 2018 (4)
  • August 2018 (5)
  • July 2018 (4)
  • June 2018 (4)
  • May 2018 (12)
  • December 2015 (1)
  • November 2015 (2)
  • December 2014 (4)
  • November 2014 (3)
  • June 2014 (1)
  • January 2014 (1)
  • July 2013 (1)
  • June 2013 (2)
  • May 2013 (3)

Meta

  • Log in
  • Entries feed
  • Comments feed
  • WordPress.org
Powered by WordPress | theme Layout Builder